davidgpo

The model number for the LCD screen is B156HAN 13.1 Replacement LCD screen was purchased on Ebay from lcdbeststore

I obtained the borescope on Amazon for about $45. It does not include a monitor. You would have to view the image through either your smartphone or your laptop. You can record stills and video. The quality is pretty good.

INGREDIENTS 1 cup warm water 1 teaspoon dry yeast 1-1/2 teaspoon salt 3 cups flour Olive oil INSTRUCTIONS Sprinkle yeast over warm water until dissolved. Toss flour and salt together and stir in dissolved yeast using a wooden spoon or fingers until dough is stiff. Turn dough on flour board 5-10 minutes, add flour as needed to prevent sticking. Dough should be smooth and elastic. Set dough in a lightly oiled bowl, cover ball lightly with oil. Cover bowl until it doubles in volume. Approx. 1-/1/2 hours. Punch down dough and divide into number of portions needed. Place dough balls on a lightly oiled baking sheet & cover with plastic pressed directly against the dough. Refrigerate until dough is roughly double in bulk, about 12-24 hours. Punch down dough and continue with recipe. Saute vegetables to soften them before adding to pizza. Bake at 500F and check at 8 minutes. It will cook faster if you bake directly on a stone or steel.

Visiting Submarine USS Blueback (581) at Oregon Museum of Science & Industry (OMSI) in Portland, OR. For details regarding problems with Torpedo Mark 14 please refer to Hidden History video: https://www.youtube.com/watch?v=JJxswaEBq4A

This is a 30mm wrench for 1/2" drive. Amazon link to the crowfoot wrench: https://www.amazon.com/Sunex-97330-2-Inch-Crowfoot-Polished/dp/B002YK9QB8/ref=sr_1_5?crid=38MJ2YZLQBEPP&keywords=30mm%2Bcrowfoot%2Bwrench&qid=1700268983&sprefix=30mm%2Bcrowfoot%2Caps%2C199&sr=8-5&th=1

This is a DeLonghi oven, model AS1870B.A. Cerakote H-Series & Elite Training Video: https://www.youtube.com/watch?v=cuqo8f_7foU&t=226s

This is a Chicago Electric Auto-Darkening Welding Helmet from Harbor Freight. Item number 91214. There are two CR2335 batteries that are soldered in. I experimented with soldering an exhausted battery and it works but I think it's bad for the battery and dangerous in that the battery can explode. Why bother soldering in fresh batteries when you would have to replace them in about 5 years? I found a battery tray that holds two CR2032 batteries in a series. See: https://www.amazon.com/dp/B07BXDHT4B?psc=1&linkCode=sl1&tag=takeabathprod-20&linkId=a558788e7d8e9aad944b86cdf120643a&language=en_US&ref_=as_li_ss_tl I replaced the lens assembly in my welding helmet so this lens will be a backup. See: https://www.youtube.com/watch?v=Y9UrPN9L7Zw This video is for entertainment purposes only. I don't recommend tampering with safety devices.

If you are going to take this on the road you will need to find the proper battery pack. Refer to: https://www.amazon.com/UY-CHAN-Programmable-Pocket-size-Acceleration/dp/B06XBFTKMY?th=1

I have a 2018 Toyota RAV4 (gasoline version) with a wimpy horn. I'm replacing the factory horns with Hella Twin Tone Trumpet horns, model 012010901, designed for Toyotas. They are rated for 113 dB.

Shinn Fu America Pro-Lift Dual Locking Jack Stands, model T-6903D. 3 Ton dual locking jack stands. Repair of the Pro-Lift Floor Jack (2020): https://www.youtube.com/watch?v=nrcoResUFec&t=649s

I have two Coleman double mantle lanterns. One is a model 220E and the other is a model 220F. Parts diagram is from https://www.oldcolemanparts.com/ A great source for parts and service.

The batteries died in my Chicago Electric Welding Helmet from Harbor Freight. Model 91214. It's 7 years old. It uses two CR2335 button batteries that are soldered in. I could not find replacement batteries with soldered tabs so I was going to place the same, without tabs, loosely in place. I thought better of it and bought a replacement lens assembly on Amazon, made by NDUUN. https://www.amazon.com/dp/B0BN1B3T74?psc=1&ref=ppx_pop_dt_b_product_details Replacement fit perfectly and seems to work properly. Harbor Freight does not have replacement parts for this model. I recommend testing your auto darkening lens prior to every welding session!

The mats may look used. That's because I've been using them for the past month.

This fan is a Lakewood box fan. My other two box fans were made by Lasko. All three have the same tip over problem. The solution is the same for all three fans.

See my first "Making Challah" video at: https://www.youtube.com/watch?v=C6x76OCAtxc&t=1s

This procedure is the same for Generation 2 model years 2004 through 2009. This video is for entertainment purposes only.

This video is for entertainment purposes only.