I Took Apart My Supercharged Corvette Engine To Fix A MAJOR Factory Defect & Make It Fast Again!
In this video, I take apart the engine on my cheap supercharged Corvette to fix a major factory defect and make it fast again! We also discover even more about this car, go for a really easy drive never going over the speed limit or spinning the tires at all, and much more. What kind of Corvette do you drive? Let me know in the comments and enjoy the show!
Check out Petris Enterprises! His instruction are HERE: https://petrisenterprises.com/collections/frontpage
Get 25% off all Amsoil products including their synthetic engine oil: https://legitoil.myamsoil.com/
Scroll down the page to "preferred customer" and click "learn more" to get the deal!
Use Coupon code Legit for 10% off Sonic Tools: https://bit.ly/3iNDtGU
http://www.creoil.com/products/cre-oil-penetrating-oil
Code Legit50 for 50% off your second bottle!
Everything car-related I recommend from Amazon: https://amzn.to/2k606u1
LSC Merch & Signature series shirts: https://www.legitstreetcars.com/
Petris Opti Diagnosis
If you suspect an Optispark failure and do not have SES codes 16 low resolution pulse, 36 high-resolution pulse, PO1371 low-resolution pulse or 1372 high-resolution pulse, check for spark output using a spark tester and fuel injector pulse with a fuel injector noid light.
The ECM/PCM requires a pulse from the Optispark whether it be on the low or high-resolution circuit to set a code. Meaning that the ECM/PCM has to see one of the two pulses to set a code for the missing pulse. The exception would be 1996-1997 LT1-LT4 with a crankshaft position sensor, they would see crankshaft rotation with no Optispark output
If the Optispark has no output whatsoever the ECM/PCM does not know that the engine is in crank mode.
If you have one of the two, spark, no fuel injector pulse or fuel injector pulse, no spark the Optispark distributor is doing its job providing a low-resolution pulse. The next troubleshooting steps would be from the PCM to the ICM and/or ignition coil.
If you have neither spark or fuel injector pulse, the wiring from the Optispark to the ECM/PCM should be tested. A multi-meter should be used to check for Optispark input voltage, ground, low and high-resolution pulses in the .24 - 4.0 volt range at the ignition system test connector located at the middle of the intake manifold on the passenger side. If you find no output or one output the Optispark has failed.
-
42:47
LegitStreetCars
2 months agoI Bought A Cheap GTR At Auction With A “Bad” Transmission & "High" Mileage! BEST DEAL EVER!
1.86K5 -
31:48
CarlCrusher
15 hours agoCurse of the Skinwalker | The Ancient Mystery of Magic Mesa - Full Documentary | Part 2
45.3K22 -
1:38
AnthiBozoviti
22 hours agoImprovisation on Ancient Greek Lyre | Anthi Bozoviti
35.7K21 -
LIVE
World Poker Tour
27 days agoWPT Live!
87 watching -
25:30
GEN
2 days ago $0.03 earnedWhat Happens When a City Decriminalizes All Drugs?
52.3K147 -
LIVE
Major League Fishing
3 days agoLIVE Tackle Warehouse Invitationals, Heavy Hitters, Day 2
73 watching -
37:24
Standpoint with Gabe Groisman
19 hours agoEp. 24. Fighting For America. US Congressman Brian Mast (R-FL)
68.4K38 -
59:12
Sports Wars
17 hours agoHarrison Butker ATTACKED By Woke Mob, Scottie Scheffler ARRESTED, Bronny James TRASHED By Scouts
79.5K55 -
4:56:56
Moroney
17 hours agoWeekend Warrior Ravin' & Trollin
74.2K2 -
30:01
World Nomac
1 day agoI Visited the Long Neck Tribe of Thailand 🇹🇭
90.1K40