M35A2 Parking Brake 4 of 4 - Making A Cable Protector
Making a copy of a deuce-and-a-half parking/emergency brake cable protector. Last in a series on how I got my parking brake working again.
6
views
LS Swap 21 - Routing And Mounting The Engine Wiring Harness
We mount the E-Rod LS3's Engine Control Module (ECM - the engine computer) and Fuse/Relay Box. Then we route all of the harness wires where they need to go, and route the fuel pump and fan wires which start in the fuse box.
Parts Used:
Chevrolet Performance 19369375 - Engine Harness (part of 19421057 E-Rod LS3 Engine Kit)
Wire And Supply GXL-10g-09 - Gray 10-gauge Copper Stranded Wire
Wire And Supply GXL-10g-13 - Light Blue 10-gauge Copper Stranded Wire
O'Reilly Auto ST81 - 3/8" Wire Terminal Clip
O'Reilly Auto ST82 - 5/8" Wire Terminal Clip
O'Reilly Auto ST83 - 3/4" Wire Terminal Clip
O'Reilly Auto ST84 - 1" Wire Terminal Clip
Hillman 4179-A - M10x20 1.50 Pitch Stainless Steel Bolt
Hillman 4122-D - M10 Stainless Steel Washer
12
views
LS Swap 20 - Clean Air For The LS3
The 1980 Camaro gets an air intake kit modified to use a GM air filter that meets emissions standards. We install a mass airflow sensor and connect a PCV hose to the intake tube.
Parts Used:
Spectre Performance 900134 - Cold Air Intake Kit
USA In Stock S03-102-BK - Black 4" 45 Degree Elbow
Chevrolet 19302206 - Dry Air Filter Element (in E-Rod kit)
ISPINNER T-BOLT-4 - 4" Stainless Steel Clamp (5)
Chevrolet 15865791 - Mass Airflow Sensor (in E-Rod kit)
Chevrolet 19166574 - Mass Airflow Sensor Bracket (in E-Rod kit)
[eBay seller jett016] - 3/8" Aluminum Hose Barb
15
views
1966 Mustang Radiator Installation
A new aluminum radiator is installed in the '66 Mustang. We hit a snag and find a way around it.
Parts Used:
Engineered Cooling Products RAD-5711S - 1965/66 Mustang Radiator
O'Reilly MBH 21953 - Upper Radiator Hose
O'Reilly MBH 20475 - Lower Radiator Hose
O'Reilly MBH 20338 - Radiator Bypass Hose
Derale 31520 - 2" Fan Spacer
Anderson Metals 756116-02 - 90-Degree 1/8 NPT Street Elbow (2)
5
views
LS Swap 19 - Radiator Hoses
Shows how we found off-the-shelf hoses from local auto parts stores for our 1980 Camaro LS swap project.
Parts Used:
Gates 21947 - Radiator Hose (upper - trimming required)
ISPINNER 1.25 Inch Stainless Steel T-Bolt Hose Clamps (2)
NAPA NBH 7460 - Radiator Hose (lower - trimming required)
ISPINNER 1.5 Inch Stainless Steel T-Bolt Hose Clamps (2)
19
views
LS Swap 18 - Radiator Installation
We install a radiator designed to cool LS engines in second-generation Camaros.
Parts Used:
DeWitts 32-6139005A - 1970-1981 Camaro LS Swap Radiator
Prothane 7-1711-BL - Radiator Support Bushings (trimming required)
Hillman 4418-D - M4-0.70 Stainless Set Screw
Gates 21947 - Radiator Hose (upper - trimming required)
NAPA NBH 7460 - Radiator Hose (lower - trimming required)
15
views
Reefer 163 Painting Time-Lapse (2023)
163 is a narrow-gauge refrigerator car built by the Rio Grande Railroad, circa 1926. A good article about it is in this issue of the C&TS Dispatch: https://friendsofcumbrestoltec.org/wp-content/uploads/2021/10/Dispatch_2023_Final.pdf.
The car was scraped and primed in 2022, before this video story begins. In 2023, volunteers worked on the car June 19th-30th, and some of that work is captured in this time-lapse.
Thanks to Jill Stewart for shooting the stenciling video, Michael Mee for taking the still photos, and Kathy Walser for locating the "before" photo.
For information on the Friends Of The Cumbres & Toltec Scenic Railroad: https://friendsofcumbrestoltec.org
6
views
Engine 483 Cosmetic Restoration Time-Lapse (2023)
Engine 483 is a K-36 2-8-2 Mikado narrow-gauge steam locomotive built in 1925. Volunteers in Chama, NM worked on it June 19-23, 2023. Here are two of those days, in time-lapse video.
Google "Engine 483 Restoration" and you will find some pre-restoration pictures of 483 that will amaze you with how far it's come.
Information on the Friends Of The Cumbres & Toltec Scenic Railroad: https://friendsofcumbrestoltec.org
7
views
1999 Dodge Viper Commercial - "Dream"
An awesome commercial that has always stirred something deep in my car-guy soul.
Originally recorded on VHS.
1
view
LS Swap 17 - Dakota Digital Oil Pressure Sensor Installation
Installing an oil pressure sending unit for a VHX gauge system from Dakota Digital on an LS3 engine. Also explains why it shouldn't be necessary.
Parts Used:
Dakota Digital SEN-03-8 - 0-100 PSI Solid State Pressure Sensor*
Chevrolet Performance 19421057 - E-Rod LS3 Engine Kit
* Part of the Dakota Digital VHX-70C-CAM-C-B - VHX Gauge Kit For 1980 Camaro
7
views
M35A2 Spare Tire Access
How do you get that spare down off the Deuce-And-A-Half so you can use it?
4
views
KEN'S 66 Mustang
To celebrate reaching 100,000 views on this channel (thanks!), here's a special look back at my all-time favorite car. An overview of the restoration and modification of a 1966 Mustang. Includes some fun footage of a Texas A&M Sports Car Club autocross.
2
views
LS Swap 18 - Fixing The Jeg's 4L70E
The "new" Jeg's transmission in Dylan's 1980 Camaro had weird symptoms: the controller reported the gear selected as Reverse in 3rd gear, and ERROR in 2nd and 1st. Worse, it felt like driving around with the emergency brake on. We fixed it - for free!
Useful Information On 2009+ 4L65E and 4L70E Transmissions:
Main Connector Pinout @2:11
Shifter Position Signal Encoding @1:34
IMS (Internal Mode Switch) Connector Pinout @5:28
Parts Involved:
Jeg's 555-603026 - 4L70E 2-wheel-drive transmission
MSD 2760 - Atomic transmission controller
MSD 2771 - Wiring harness for 2009+ 4L70E
GM 24235261 - Internal Mode Switch*
* May be obsolete. 24248867 may replace, but I haven't seen one.
4
views
LS Swap 17 - Jeg's 4L70E: Seven Deadly Sins
The 4L70E transmission seemed like a great choice for our 1980 Camaro LS swap, because it's designed to handle more power than a 4L60E or 4L65E. Jeg's was offering it for a good price. What could go wrong?
A 4L60E or 4L65E could just as easily have had these issues, so you guys listen up too!
Parts Used:
Jeg's 555-603026 - 4L70E 2-wheel-drive transmission
14
views
1980 Camaro Steering Column Rebuild, 4 of 4 - Installation
We repair the threads of nuts on the firewall, then install the column. Attachment of the intermediate steering shaft is briefly shown, but is given proper attention in a separate video.
Parts Used:
Rubber The Right Way 18-003P - Steering Column Floor Seal
LS Swap 16 - Dakota Digital Coolant Temperature Sensor Installation
The too-simple-to-fail job of installing our VHX gauges' temp sending unit onto the LS3 goes awry in multiple ways, with a single root cause.
Parts Used:
Dakota Digital VHX-70C-CAM-C-B - VHX Gauge Kit For 1980 Camaro
Chevrolet Performance 19421057 - E-Rod LS3 Engine Kit
12
views
Review - Husky 84 Inch Workbench Tool Chest
A brutally honest review of my new 84"W x 24"D Mobile Workbench With Stainless Steel Work Top from Home Depot.
Model Number: HOTC8422BB1M
Store SKU: 1006201604
3
views
LS Swap 14 - Custom Power Steering Hoses For A 1980 Camaro
How we connected the E-Rod LS3's Holley power steering pump to the Camaro's stock power steering gearbox.
Parts Used:
Precision 13502383 - Low Pressure 3/8" Power Steering Hose (2 feet)
Precision 23602826 - Low Pressure Hose End Fitting*
Precision 13401312 - High Pressure Power Steering Hose*
* Borrowed to use as a reference.
12
views
LS Swap 13 - Installing A Power Steering Pump And Serpentine Belt On An LS3
With the installation of the power steering pump, all accessories have been installed, so we are able to install the serpentine belt.
Parts Used:
Holley 198-101 - Power Steering Pump With Reservoir*
Holley 198-203 - Power Steering Hard Line To -6 AN Fitting*
Holley 97-152 - Power Steering Pulley*
Bando 6PK1715 - Serpentine Belt*
* Part of the Holley 20-185 Mid Mount Accessory Kit
5
views
1980 Camaro Steering Gearbox And Pitman Arm, 2 of 2 - Installation
Dylan installs the Steering Gearbox and attaches the Pitman Arm.
Parts Used:
NAPA 39-1075 - Steering Gearbox
1980 Camaro Steering Gearbox And Pitman Arm, 1 of 2 - Removal
Dylan removes the Steering Gearbox from the front subframe, then removes the Pitman Arm from the gearbox.
LS Swap, 12 of ? - Installing Steam Tubes On An LS3 Engine
Dylan makes his own steam tubes and plumbs them to the back of the Holley water pump.
Parts Used:
Earl's Performance LS9807ERL - LS Steam Vent Adapters
Fragola 482603-BL - Aluminum Tee Fitting, 1/8 NPT, -3 AN
Summit Racing SUM-220333-6N - Tube Nuts, -3 AN
Summit Racing SUM-220334-6N - Tube Sleeves, -3 AN
Carlson H8350NC - 3/16" Copper Nickle Line
2
views
1980 Camaro Steering Column Rebuild, 3 of 4 - Assembly
Dylan reassembles the steering column of the '80 Camaro. We do something dumb and make a lot of extra work for ourselves.
Parts Used:
GM 07844651 - Rack Kit
GM 1990096 - Tilt Wheel Ignition Switch
GM 1995963 - Turn Signal Switch
NAPA KS6186 - Ignition Lock Cylinder Housing Repair Kit
Classic Industries A8100507 - Lower Steering Column Bearing Assembly
Classic Industries G13060 - Lock Plate Retaining Ring
2
views
Installing A Starter On An LS3 Engine
Dylan installs the starter for the LS3, and learns a painful lesson.
Note: Wiring will be covered in a future video.
Parts Used:
NAPA RAY-2465164 - Starter With Solenoid (for 2013 Corvette)
NAPA 656-1527 (two) - Starter Bolt
GM/ACDelco 24261712 - Transmission Case Cover