MarriedEdgeDIY

Installing a replacement vent or quarter window on a 2003 Toyota Camry

Replacing the window switch on a 2005 Ford Expedition

Showing the basic stock removal method of making a knife by simply cutting out the shape with a grinder

How to anneal carbon steel to make it soft for drilling and file work. Blacksmithing, knife making

In this video I show you how to determine if a piece of steel has a high enough carbon content to be made into a good knife. I will show annealing, normalizing, quench and tempering in future videos

Replacing a broken propeller on an 86 Mercruiser Alpha One

This was a failed attempt to stop an oil leak from the valve cover of a 99 s10 with a 2.2. The PCV system on these motors is internal incorporating the intake manifold gasket and valve cover baffles. As the system ages the manifold gasket has a small hole that can become clogged and the valve cover baffles can develop a leak when the silicone on the baffles breaks down

Replacing the charging port on a Samsung Galaxy A01 smart phone. One of the easiest repairs I've come across, good starting point for getting yourself comfortable working on smart phones.

Part one of building a propane forge from a Sears & Roebuck's pot belly stove

In this video I'm lining the forge with refractory material comprised of kitty litter, sand and ashes

How to do a basic oil change at home without special tools. Happens to be on a 99 S10 with a 2.2. But should give you what you need to figure it out on any vehicle. Also what to do with your used oil

Quick explanation of the parts comprising the PCV system on the Chevy 2.2L motor found in the S10, Cavalier and other vehicles

Explaining the necessary ingredients to make a propane forge burner at home

Anchoring hinge posts to a block column using 1/2"x6" Tapcon concrete fasteners https://rumble.com/vs94xu-entry-gate-part-1-design-phase.html

Pouring and finishing concrete column caps https://rumble.com/vs94xu-entry-gate-part-1-design-phase.html https://rumble.com/vscqbt-entry-gate-part-2-layout-and-dig-footings.html https://rumble.com/vsesa4-entry-gate-part-3-forms-and-rebar.html https://rumble.com/vtoj7k-entry-gate-part-5-columns.html https://rumble.com/vu0f18-entry-gate-part-6-grouting-cinder-block-columns.html https://rumble.com/vw14dy-entry-gate-part-7-split-rail-fence.html https://rumble.com/vwjxuk-entry-gate-part-8-column-cap-forms.html

Forming the column caps and preparing for concrete https://rumble.com/vs94xu-entry-gate-part-1-design-phase.html https://rumble.com/vscqbt-entry-gate-part-2-layout-and-dig-footings.html https://rumble.com/vsesa4-entry-gate-part-3-forms-and-rebar.html https://rumble.com/vtoj7k-entry-gate-part-5-columns.html https://rumble.com/vu0f18-entry-gate-part-6-grouting-cinder-block-columns.html https://rumble.com/vw14dy-entry-gate-part-7-split-rail-fence.html

Installing split rail fence posts and rails in concrete https://rumble.com/vs94xu-entry-gate-part-1-design-phase.html https://rumble.com/vscqbt-entry-gate-part-2-layout-and-dig-footings.html https://rumble.com/vsesa4-entry-gate-part-3-forms-and-rebar.html https://rumble.com/vspww2-entry-gate-part-4-column-footing.html https://rumble.com/vtoj7k-entry-gate-part-5-columns.html https://rumble.com/vu0f18-entry-gate-part-6-grouting-cinder-block-columns.html

Replacing the brake rotors, pads, wheel bearings and seal on a 99 chevy s10 2wd rwd

Installing Maxtrac 3 inch lift spindles on a 99 Chevy S10 2wd rwd

Removal and replacement of a clutch slave cylinder and throw out bearing on a late model Chevrolet s10. Similar to a Ford slave cylinder as well

There's limited information available on the 2.2 S10 cylinder head 24576146. If you purchase a remanufactured engine you are likely to run into this issue of no EGR bolt holes for the plate that covers the EGR hole. Apparently on the GMC Sonoma this hole is incorporated into the intake manifold. On the S10 it is simply blocked off

Installing a clutch and pressure plate on a 99 Chevrolet s10 2.2 liter engine

Bench bleeding a hydraulic clutch slave cylinder for a 99 chevrolet S10 2.2 liter manual transmission. Same set up for various years and vehicles including some Ford models

Building the columns on the front drive way entry gate https://rumble.com/vs94xu-entry-gate-part-1-design-phase.html https://rumble.com/vscqbt-entry-gate-part-2-layout-and-dig-footings.html https://rumble.com/vsesa4-entry-gate-part-3-forms-and-rebar.html https://rumble.com/vspww2-entry-gate-part-4-column-footing.html

Replacing the fuel pump on a 99 chevy s10