CastleRemodel

Borax: https://amzn.to/3wWEGVG Sugar: https://amzn.to/452kM8g Follow Me On Locals: https://homeremodel.locals.com/ Get The Free My Home Maintenance Checklist: https://castleremodel.com/checklist/ Visit My Blog: www.CastleRemodel.com Hi Folks, Kevin with another video for you. This video shows you how easy it is to make a diy ant bait. There is a chance you already have the ingredients at home. You want to use equal parts borax and sugar. You don't need much water, just enough to make it pasty. Thank you for watching this video. Here at Kev’s Castle I am dedicated to help you “create your castle.” I do that by showing you the best tips and tools to finish your home remodel jobs. If you have any questions please leave it below. I read every question and do my best to reply to all of them. Please forgive me if I am late to reply to you. Thanks for watching. Happy Remodeling, Kevin

EGO Power+ Electric Lawn Mower: https://amzn.to/3R0gw3e Follow Me On Locals: https://homeremodel.locals.com/ Get The Free My Home Maintenance Checklist: https://castleremodel.com/checklist/ Visit My Blog: www.CastleRemodel.com Hi Folks, Kevin here with another video for Kev's Castle. This video walks you through all the information you need to know about using the EGO electric lawn mower. This is a great lawn mower if you are considering it. I hope this video helps you with the information you need to know. Thank you for watching this video. Here at Kev’s Castle I am dedicated to help you “create your castle.” I do that by showing you the best tips and tools to finish your home remodel jobs. If you have any questions please leave it below. I read every question and do my best to reply to all of them. Please forgive me if I am late to reply to you. Thanks for watching. Happy Remodeling, Kevin

Follow Me On Locals: https://homeremodel.locals.com/ Get The Free My Home Maintenance Checklist: https://castleremodel.com/checklist/ Visit My Blog: www.CastleRemodel.com Hi Folks, In this video I show you how to clean the washing machine filter. It is an easy task that often gets overlooked. It doesn't take long at all. When I cleaned the filter in this video it took me about 20 minutes. The first step is to locate where the filter is on your washing machine. This is usually on the front near the ground on a front loading washing machine. If it is not here on your washing machine you will want to consult the manual. Once you find the filter on your model the process of cleaning it is usually the same as what is shown in this video. You want to drain the residual water out first by using the hose that is attached nearby. Place the end of the hose in a shallow bin, and let the water drain out. Dump the water down the drain or in a toilet. when you dump the water you want to make sure you keep the hose elevated. There may be more water in the line that will try draining out, and you don't want to get it on the floor. Once you have drained all the water out you want to make sure the cap is placed back on the end of the tube. Double check that it's secure because if it comes loose it will flood your floor the next time you do laundry. After this part is done you can remove the filter. This is a knob that is near the tube you just leaked. Turn it to the left (counterclockwise) and take it out. Take this to a sink to clean it. You may want to use a tray to carry this to a sink. It's probably going to drip and the water is pretty nasty. There also may be a tangle of hair stuck in the filter. This can be pulled or cut out. After this is cleaned off you can put it back. Turn it to the right to lock it in place. Close the door and you are finished. Congratulation! Thank you for watching this video. Here at Kev’s Castle I am dedicated to help you “create your castle.” I do that by showing you the best tips and tools to finish your home remodel jobs. If you have any questions please leave it below. I read every question and do my best to reply to all of them. Please forgive me if I am late to reply to you. Thanks for watching. Happy Remodeling, Kevin

Drywall Anchors: https://amzn.to/3UORdDJ Picture Hanging Kit: https://amzn.to/3JSPZ46 Picture Wire: https://amzn.to/3WwIkzX Hammer: https://amzn.to/4btBfVe Screwdriver: https://amzn.to/3yifk4J Get the free My Home Maintenance Checklist: https://castleremodel.com/checklist/ Hi Folks, Kevin here with another video. In this video I'm showing you two methods on how to hang pictures on the wall. The first method is with a heavy duty anchor that can hold up to 20 pounds. This method is how I use wire to "anchor" the picture to the wall. I show you my method to make sure the picture doesn't fall off the wall on accident. This is important if you have a picture you don't want to get damaged. There are situations that might cause the picture to fall of the wall, causing it to get damaged. The second picture hanger is used to hold lighter weight pictures. You can see the exact hardware I use by clicking the links above. I also created a free home maintenance checklist for you. It is used to help keep you up to date on what maintenance routines need to be done and at which times. Click the link above to get your free copy of My Home Maintenance Checklist. If you like this video please give it a thumbs up. It helps others find the videos as well. And if you want to see more videos like this click the subscribe button. Here at Kev's Castle I am dedicated to helping you create your castle! If you have a question for me or would like to say something about this video please leave a comment. I try hard to get back to every comment. Thanks for watching. Happy Remodeling, Kevin

Shark CarpetXpert: https://amzn.to/3JQvbKs Stain Striker Bundle: https://amzn.to/44vswPP Get My Home Maintenance Checklist: https://castleremodel.com/checklist/ Hi folks, Today's video is bringing you my unboxing and opinion about the Shark CarpetXpert carpet cleaner. I open it up and show you everything that's included. In this video I also show you how to set up the cleaner. Finally we use it on a pretty dirty carpet. At the end of the video I give you my honest opinion on the product. You will find out what I truly think about it, and how to use it. There were a few things that confused me while using the Shark CarpetXpert. I will show you what tripped me up, and what I learned about how to get past these problems. If you are in the market for a new carpet cleaner I recommend considering the Shark Carpet Xpert. It has plenty of features that I liked to make it a good choice. The main reason why we chose this model is because it has tanks that get filled with the cleaner. The nice thing about this is you can add the cleaning solution of your choice and it will still work fine. You don't need to purchase the manufacturer's brand name cleaning solution. All in all I rate this model an 8.5 out of 10. It is easy to use, and doesn't take long to figure out. The times that I had problems with it didn't take long before I figured out what to do. I recommend checking out this model at the link above. If you got value out of this video please give it a thumbs up. And if you want to see more videos like this make sure to subscribe. Check out the blog at www.CastleRemodel.com Here at Kev's Castle I am dedicated to helping you create your castle! Thanks for watching and I look forward to seeing you in the next video. Happy Remodeling, Kevin

Toilet: https://amzn.to/4dmaTpJ Channellock Pliers: https://amzn.to/4diq4QN Nitrile Gloves (Large): https://amzn.to/3xZjT41 Flat Screwdriver: https://amzn.to/3Uo3CNn Paint Scraper: https://amzn.to/4bloonZ My Home Maintenance Checklist: https://castleremodel.com/my-home-maintenance-checklist/ See me on Locals: https://locals.com/member/CastleRemodel Buy me a coffee on Ko-fi: https://ko-fi.com/castleremodel Hey Family, Keven here with Kev's Castle and CastleRemodel.com. This video walks you through the steps on how to install a toilet. This project isn't hard at all, just take the steps listed in this video and you will be fine. The most important thing to remember when you are doing this project is to not over-tighten anything because the toilet is made of porcelain. This material will crack at a certain point, and we don't want that, do we? Removing the old toilet might be awkward, but you can remove the tank if you need to. It also helps if you have someone to help you carry the old one. The new toilet can be assembled in place, and each of the parts aren't that heavy. I hope this video helped you out. If you got value out of it I'd appreciate you hitting the like button. And for more videos like this tap the subscribe. Check out my locals page for more valuable content. the link is https://locals.com/member/CastleRemodel Thanks for watching. Happy Remodeling, Kevin

My Home Maintenance Checklist: https://castleremodel.com/my-home-maintenance-checklist/ Miter Saw: https://amzn.to/3JEhWg0 Buy me a coffee at Ko-fi.com: https://ko-fi.com/castleremodel Hello and welcome to the Kev's Castle channel. In this video I am going to show you how to use a miter saw. I will walk you through various topics like: personal safety, how to measure and make a mark to cut, how to cut properly, how to adjust the angle and more. If you have a miter saw, and are ready to use it, it's important that you watch this video. I want you to learn the proper way to use a miter saw. I walk you through the steps on how to make a cut while being safe. If you like this video please give it a thumbs up. If you want to see more videos like this in the future please hit the subscribe button. Here at Kev's Castle and CastleRemodel.com I am dedicated to helping you turn your home into a sanctuary! Thanks for watching and happy remodeling. Kevin

Double Curtain Rod: https://amzn.to/3wTjakh Blackout Curtain: https://amzn.to/4cfOTwd Sheer Curtain: https://amzn.to/3wWJfz7 DeWalt Drill: https://amzn.to/3IFS9n5 Bit Set: https://amzn.to/4cfcugz Stanley Tape Measure: https://amzn.to/3VDixWz Franklin Sensor Stud Finder: https://amzn.to/49PB7Pg Screwdriver: https://amzn.to/4clqzsI Mallet: https://amzn.to/3vhlt07 Pencils: https://amzn.to/43mxkq5 Hey folks, In this video I show you how to install a double curtain for blackout shades. The curtain rod is a double rod so you have the option of having either a blackout shade, or a sheer blind on your window. This gives you two very cool options to choose from. The first step to installing the curtain rod is to find the studs. This is going to be the best option for how you install it because if you use drywall anchors you have a good option of accidentally pulling them out when you open or close them. once you have located the studs, you will want to install the brackets one either side of the windows. Make sure the window is centered between the curtains. after the brackets are installed you will be able to attach the rods. There are pieces that slide over the brackets and hook on using a set screw. Use the supplied allen key to screw in the set screw. After the two end pieces are on it's time to put the rods up. But first you want to slide the curtains on. The curtain you choose will depend on if you are putting up the sheer curtain or the blackout curtain. The two different curtain rods are different thicknesses, and will need to be paired up with the correct match. after both rods have their curtains on them, and are hanging up correctly, it's time to put the center piece up. This will help support the weight of the curtains. Find the center between the two end points of the curtain rod. Make a mark on the wall and hold the bracket up to the curtain rods. Mark the holes for the bracket. this is where you are going to drill pilot holes. Check if there is a stud there you can screw in. If there isn't you can use the anchors. Install the anchors in the holes you made, and use them to screw up the bracket. After this bracket is up, you are done installing your curtain rod. Give them a test pull to see how they slide. Congratulations on installing your blackout curtains. I hope you liked this video. If you got value out of it please give it a thumbs up. Hit that subscribe button for more videos like this. Here at Kev's Castle I am dedicated to helping you turn your home into your personal sanctuary. Check out the blog for articles and other cool stuff to help you. The blog can be found at: www.CastleRemodel.com Thanks for watching, Kevin

Pry Bar: https://amzn.to/3wBhfAJ Hammer: https://amzn.to/3IkEaCW Torpedo Level: https://amzn.to/3TlJ1tW Drill Bit Set: https://amzn.to/434sOg7 Wood Screws: https://amzn.to/3P5qteW Finish Nails: https://amzn.to/3V3rhEV Wood Shims: https://amzn.to/3T5Fkae Electric Drill: https://amzn.to/430Uoum Multi Tool: https://amzn.to/3TiVdLU In this video I show you how to fix a door that sticks at the top. You don't need to cut the door down, or altar the door jamb at all. The only way to fix it is to first understand what is causing the problem. If a door is sticking at the top, it is probably because the house is settling, and one of the jambs sunk slightly. After recognizing this issue, you can then go about fixing it the right way. Remove the casing from the side of the door that is sticking. And remove the casing from the top. will need to remove the casing from both sides of the door. The casing on the side that isn't sticking does not need to come off because we will not be doing anything to this side. This is the side of the door that we are going to try to duplicate on the other side of the door. If we can do this the door jamb at the top will be level and the door will stop sticking. Once the casing is off in these locations, you want to cut the screws or the nails that are holding the jamb to the wall. Make this side of the door loose to be able to level it. Use the multitool with a metal cutting bit to cut the screws or nails. Then the level will help make the jamb level. Put some shims behind the jamb on the side you are trying to fix. You don't need to put any at the top. Put one or two screws at each part you have shims at. You only need them in three locations (top, middle, and bottom). Drill pilot holes for the screws at these locations. After you install the screws, and both the top and side jambs are level, you can put the casing back on. Make sure the corners are square, and then nail them back on. If you were careful removing the casing, you can reuse it. But if you damaged it too much you may need to replace the pieces with new ones. There is one way to fix it the right way. Take your time, and go methodically. I hope you liked this video. Please give it a thumbs up if you took value from it. And hit the subscribe button to get more videos like this in the future. Thank you for watching Kev's Castle. Please visit the blog for articles that cover topics like this, and much more. You can find the blog at: www.CastleRemodel.com Happy Renovating, Kevin

Bathroom Fan: https://amzn.to/3IdFUxE DeWalt Drill: https://amzn.to/48x0NyE Drill Bit Extension: https://amzn.to/42TgizG 4" Hole Saw: https://amzn.to/3TecaqZ Wire Stripper: https://amzn.to/3wwYe2p Hello and welcome. In this video I show you how to install a bathroom fan where there wasn't one already. I will walk you through all the steps of the process, including: How to mark and cut the hole for the fan. How to drill into the outside of the house How to connect the wiring to the fan. how to mount it to the ceiling. I also have articles on the blog that cover this topic, and many more. You can find the blog by going to... www.CastleRemodel.com If you like this video please give it a thumbs up. And hit that subscribe button so you can be the first to get the new videos I release. I am devoted to helping you turn your home into your sanctuary. I cover topics like home remodeling and maintenance. I also show you how I am remodeling my home, turning it into what we want it to be. Welcome to the journey. Thanks for watching, and I look forward to seeing you in the next video. Happy Remodeling, Kevin

InSinkerator 1/3 hp Garbage Disposal: https://amzn.to/47C2eeL Multi Screwdriver: https://amzn.to/3vzY1Lb Oatey Plumber's Putty: https://amzn.to/3vBlD2a Electrical Tape: https://amzn.to/3U36QY3 If you don’t know how to install a garbage disposal, it would feel practically impossible. The truth is you don’t need any special tools to install one. In fact, this article will show you that anybody who knows a few DIY basics can install it in about an hour. Read this article to get a hassle-free guide on how to install a garbage disposal. There are many garbage disposals to choose from. If you haven’t decided on one for your home yet, then I am going to recommend the Insinkerator Badger 1 model. It is ⅓ horsepower, which is plenty of power for your home’s kitchen. Click the link below to take a look at it. Installing a garbage disposal is easier than you might think. This article is going to show you how to install one if you have electrical power under your sink. There are two forms this power can come in. The first is for there to be a power outlet that is available under the cabinet. The second is for it to have a hardline connection directly to the garbage disposal. Required Tools: Oatey Plumber’s Putty Hacksaw Flat Screwdriver Wire Strippers How To Install a Garbage Disposal in a Double Sink The steps outlined here include how to install a garbage disposal with and without a dishwasher. If you have a dishwasher connected to your existing garbage disposal, you will follow the steps outlined below for that. If there is no dishwasher connected, skip those steps. Turn Off The Power The first step for any job that you are working on anything that has electricity running to it is to turn off the power at the breaker box. This can be easy if you have a well labeled panel. But if it isn’t labeled very well it might be a guessing game. Test if the power is off before you make any assumptions. The easiest way to do this is to flip on the switch for the garbage disposal. It is safe to begin if it doesn’t come on. Remember to flip it off though, because you don’t want the new garbage disposal to turn on when you turn the power back on. This is also the right time to remove any products that are in the way. Find a place to put as many of them as possible. You want to have as much working space as you can. For the installation. Disconnect The Old Garbage Disposal There will be two screws attached to the discharge pipe. Back those out all the way and set them aside. If there is a dishwasher attached to the disposal this is a good time to remove the hose that attaches it. To do this turn the screw on the pipe clamp counterclockwise until the clamp is loose. Then pull the connection off the garbage disposal. There are also three screws facing upward just beneath the sink. Loosen each of these about half way. If you use a screwdriver for two of them, the third should be able to loosen by hand. You want to back them out enough to lift the bottom of the bracket up towards the sink. Once these screws are loose and the drain pipe is disconnected from the garbage disposal, hold the bracket steady with one hand and twist the garbage disposal to the left with the other. This should pop it loose. After it is movable, take a flat screwdriver to pop off the metal ring that is holding the pieces of this bracket together. To do this first slide all the parts upwards towards the sink. This will allow the ring to be visible. While holding them up with one hand, use a flat screwdriver in your other hand to slide the ring downward. Is the garbage disposal plugged into a wall outlet, or is it hardlined in? If it’s plugged in you can simply pull the plug out and the garbage disposal will be free to move. You will need to attach a power cord to the new garbage disposal, and may need to reuse the old cord. Both methods are the same from this point on. If it is hard lined in, you will need to remove the wires before you can lift the disposal away. To do this simply turn the disposal upside down, or lay it on it’s side with the bottom facing you (whichever one is easier for you). There is a small metal plate with one screw in it near the location the wires go into the bottom. Remove this screw. There should be two wire nuts, and one grounding wire screw. Remove the wire nuts, and loosen the screw. Once all three wires are free you should be able to pull them out. You may want to clip them close to the location they were twisted if this is easier. Disclaimer: Only clip them if you have plenty of length on your wire left. Also only do this if you have a wire stripper handy and are comfortable with stripping the wires later. It can be a larger problem if there isn’t enough length to hook up the new disposal. You also want to remove the connector the wires are going through. There are a couple of screws that can be removed. Once the wires are pulled out you can turn this connector counterclockwise to remove it.

The Contractor Search Guide: https://castleremodel.com/contractor-guide-landing-page/ Hi, At Kev's Castle and www.CastleRemodel.com I am devoted to helping you turn your home into a sanctuary. In this video I update you on the basement remodel project taking place in my house. We needed a contractor to do this work because it is not something I feel super comfortable with. It will feel great to have the work done shortly. But until then we are having him work on it instead of me. If you are looking for a contractor for your remodeling project, I created a guide to walk you through the steps to do so. Click the link in this description to check out The Contractor Search Guide. It will walk you through everything you need to know to hire a reliable contractor that won't be more hassle than they are worth. This guide shows you where to go to look for a good contractor. You need to know the right places to look if you want to find a good person to hire. Next you get a downloadable list of interview questions. The questions also show you what to look for in their answer to help determine if they are a good candidate for your project. And last but not least there is a thorough section that discusses everything you need to know about drafting a contract. The contract is possibly the most important stage of the process. It protects you from any issues that may arise. Pick up The Contractor Search Guide to shield yourself from a horrible contractor. The Contractor Search Guide: https://castleremodel.com/contractor-guide-landing-page/ If you liked this video please give it a "thumbs up". And if you want more videos like this where I show you what I am doing to turn my home into my sanctuary then please hit the subscribe button! Thanks for watching, Kevin

The Contractor Search Guide - https://castleremodel.com/contractor-guide-landing-page/ Hi, In this video I walk you through the steps on how to pour concrete. We cover how much water to add, what the best tool is to use, and what consistency you want it to be when you're done. I hope this video helps you with what you are looking for. If you like this video please give it a "thumbs up". And hit that subscribe button for more videos like this. Visit my blog for more information about home remodeling. It's called Castle Remodel. It's where you go to learn how to turn your home into a sanctuary. www.CastleRemodel.com Thanks for watching, Kevin

Kwikset Front Entry Smsartkey Doorknob - https://amzn.to/47yrL9f DeWalt 20V Drill - https://amzn.to/3G2tNCt Screwdriver set - https://amzn.to/3G2tRlH 4 Piece Chisel set - https://amzn.to/47wYFXN Visit the blog: www.CastleRemodel.com Hey folks, Thank you for watching another episode of Kev's Castle. In this video I teach you how to install a new exterior door knob. You will learn how to remove the old door knob. And you will also learn how to install a new door knob. I like using power drill to remove the old door knob. But that is not the best tool for installing a new door knob. This is because you may run the risk of stripping the screw head with the power drill. Installing a new door knob is very easy, if you know how to do it. Don't cut any corners, take your time, and you will do fine. Thank you for watching this video. Please leave a comment below if you have any questions. -Kevin

Mail Boss 7526 Mailbox: https://amzn.to/3RxYTZR Mail Boss 7121 Post: https://amzn.to/3t6m0k9 Stanley leverlock Tape measure: https://amzn.to/3Ps0PjN Level: https://amzn.to/3PMsxcA Socket set: https://amzn.to/3RwwSSw Post hole digger: https://amzn.to/3rtCMsM Shovel: https://amzn.to/3PqvgHf Clamp: https://amzn.to/46dteky Blog: www.CastleRemodel.com Here at Kev's Castle I am dedicated to show you how to turn your home into your personal castle! I will be bringing you along on my journey of remodeling my home. In this video i show you how to install a mailbox and post in concrete. I go through the steps on how to determine the location of the post hole. Also you will learn what depth you will want to make the hole. I then show you how to keep the post level while and after pouring the concrete. If you like this video please remember to give it a thumbs up. Hit that subscribe button to be notified when I upload more videos like this. Thank you for watching Kev's Castle! -Kevin

Lutron Sunnata Dimmer Switch - https://amzn.to/447pRLb Wire Stripper/cutter - https://amzn.to/3NXT0mv Screwdriver - https://amzn.to/3JHrDuh Electric Tape - https://amzn.to/3O8wI1H Electric Tester - https://amzn.to/3NJqtzY In this video you will learn how to install a dimmer switch for a light. The switch in this video is located in the dining room. There is only one switch for this light, but if you have a light that has two or more switches the dimmer I use is a good option also. You will be able to use the switch I highlight in this video for a light in your home that has more than one switch connected to it. I cover why I chose this switch, as well as all the steps you should take when installing it. If you like this video, and would like to see more like it, please click that subscribe button below. I will be putting out more videos like this that help you turn your home into your personal sanctuary. Happy renovating, Kevin

Blog Articles: https://castleremodel.com/smoke-detector-placement/ https://castleremodel.com/best-smoke-detector-and-carbon-monoxide-detector/ Tools and Smoke Detector In Video: Smoke detector: https://amzn.to/42L2k2p Drill: https: //amzn.to/3zhloru Drill bits: https://amzn.to/3G15KV8 Driver bit: https://amzn.to/40ngN3a Tape measure: https://amzn.to/40kp87A Stud finder: https://amzn.to/40L11yz Safety glasses: https://amzn.to/3TTkzyx Step ladder: https://amzn.to/3lPGfz7 In this video you will learn how to install a battery operated smoke detector. I install a Kidde brand smoke and carbon monoxide detector (2 in 1). I talk about the proper placement of the smoke detector on both the ceiling and the wall. I also show you how to use a stud finder to find a stud. I included 2 articles I wrote about smoke detectors. The first one explains the proper placement of smoke detectors. It covers topics like what room to put a smoke detector or co detector in. Also where on the wall or ceiling is ideal placement for one. I include a chart I made that talks about laws in all 50 states regarding smoke and co detectors. The second article discusses what the best options for smoke detectors are. It shows you all the options on where a smoke or carbon monoxide detector might be used, and what the best model is for that option. If you liked this video, please give it a thumbs up. I will be putting out a lot more content like this that will help you turn your home into your sanctuary. So if you want to see more videos like this hit that subscribe button. Thanks for watching, Kevin